-Anomaly

fter your purchase please make sure to follow this Pre Requirements Video, otherwise cheats wont work. You can download the MadChad support tool as seen on the Video HERE.

Pre Requirements Video:

Before using Anomaly, make sure your system meets the following requirements and settings:

• SVM [AMD] / VT-X [INTEL] must be enabled in BIOS • 16 GB RAM or more is required • Hyper-V must be disabled for AMD CPUs only • Hyper-V must be enabled for INTEL CPUs only • Secure Boot must be disabled

⚠️ Supported platforms: INTEL & AMD CPUs, Windows 10–11 (1909 – 25H2). Failure to meet these requirements may result in the loader not working or the cheat failing to initialize.

Setup

SteelSeries supported fullscreen: https://steelseries.com/gg/download/ To use SteelSeries, go to settings in the GENERAL -> General section, turn on Sonar, then go to the SONAR -> Shortcuts tab, put the "F7" key on the Master - Volume Up, you need to press this bind before injection

GeForce Experience not supported fullscreen: https://www.nvidia.com/en-eu/software/nvidia-app/ To use NVidia app overlay, you need to open the settings, go to Generals and enable IN-GAME OVERLAY

Before launching, you need to enable NVidia app overlay, if you have an AMD graphics card, then you need to install SteelSeries. Nvidia graphics cards support NVidia app and SteelSeries, AMD graphics cards only support SteelSeries.

Loader - http://undetect.net/download/loader

1. To launch our product, you will need: Disable the antivirus

2. Launch the loader

3. Insert the key

4. Press the inject

After inject, the loader will close itself, which means that you can start the game The menu is called by the "Insert" button

🛠️ Troubleshooting & Common Errors

Below are the most common errors and their solutions. Follow the steps carefully.

---

❌ Error: Please launch SteelSeries Moment Overlay (FOR GEFORCE)

Solution:

• Disable GeForce Overlay

• Re-enable GeForce Overlay

• Restart the game and loader

---

❌ Error: Please launch SteelSeries Sonar Overlay (FOR STEELSERIES)

Solution:

• Press your SONAR overlay bind

• Only launch the loader after the overlay is active

---

❌ Issue: Menu flickering or black screen in game

Solution:

1. Open SteelSeries

2. Go to Settings → Moments → Capture & Sound

3. Disable “Allow Moments to Capture While Gaming”

4. Restart the game

---

❌ Error: Please disable Intel Rapid Storage Technology

Solution:

• Intel RST must be disabled

Instructions: https://answers.microsoft.com/en-us/windows/forum/all/uninstalling-the-intelr-rapid-storage-technology/e3c4b6d6-56ba-4ac5-be50-89843c9d9b22

---

❌ Error: Bind button does not work

Solution:

• Re-inject the cheat

• If the issue persists, run the overlay as Administrator

---

❌ Error: No menu appears / loader closes instantly

Solution: Install Microsoft Visual C++ Redistributable (x64): https://aka.ms/vs/17/release/vc_redist.x64.exe

Restart PC after installation.

---

❌ Error: Unsupported Firmware

Solution:

• Convert system disk to GPT

• Switch BIOS from Legacy → UEFI

---

❌ Error: 0x296

Solution:

• Re-inject the cheat

---

❌ Error: Unknown network error

Solution:

• Check your internet connection

• Disable VPN if active

• Restart router and try again

---

❌ Error: Failed to allocate memory / Failed to map memory (x)

Solution:

1. Reboot your PC

2. Try again

If the issue persists:

• Clean startup programs

• Download Autoruns: https://learn.microsoft.com/en-us/sysinternals/downloads/autoruns

• Disable all non-system startup entries

⚠️ Old drivers from removed software may cause this issue.

---

❌ Error: Failed to load dependencies (x / -x)

Solution:

• Disable ALL antivirus and protection software

• Remove anti-cheats / anti-readers

• Clean startup programs using Autoruns

---

❌ Error: Please uninstall Vanguard / FaceIT first

Solution:

• Fully uninstall Vanguard and FaceIT

• Restart your PC

• Launch again

---

❌ Error: AES instruction set is not supported

Solution:

• Your CPU does not support AES

• This issue cannot be fixed

---

❌ Error: Please enable Intel VT-X / AMD-V

Solution:

1. Enter BIOS

2. Enable one of the following:

   • Intel Virtualization Technology

   • Intel VT-X

   • AMD-V

   • SVM Mode

3. Save and reboot

---

❌ Error: VMX / SVM is not supported

Solution:

Step 1 – Disable Windows Virtualization

• Control Panel → Programs → Enable or Disable Windows Features

• Disable:

  • Hyper-V

  • Virtual Machine Platform

Step 2 – CMD Fix

Open Command Prompt as Administrator and run:

bcdedit /set hypervisorlaunchtype off

Reboot PC.

Step 3 – Windows 11 Advanced Fix (if still not solved)

Run PowerShell as Administrator and paste ALL commands below 1 by 1:

takeown /F "C:\Windows\System32\hvix64.exe"
icacls "C:\Windows\System32\hvix64.exe" /grant *$(([System.Security.Principal.WindowsIdentity]::GetCurrent()).User.Value):F
takeown /F "C:\Windows\System32\hvax64.exe"
icacls "C:\Windows\System32\hvax64.exe" /grant *$(([System.Security.Principal.WindowsIdentity]::GetCurrent()).User.Value):F
del "C:\Windows\System32\hvix64.exe"
del "C:\Windows\System32\hvax64.exe"

---

❌ Error: Virtual or RAID disk detected

Solution:

• Disable spoofer or

• Disable RAID in BIOS

• Reinstall Windows in normal (non-RAID) mode

---

❌ Error: CRD failed / Failed to init render

Solution:

• PC: GPU is too old / unsupported

• Laptop: Disable integrated GPU in BIOS